Whip Mix Pro Press 100 Manual del operador

ProPress SP FurnaceOperator's ManualWhip Mix Corporation • 361 Farmington Ave. • P.O. Box 17183 • Louisville, KY 40217-0183 USA 502-637-1451 • 80

10ProPress SP Furnace Operations Manual Chapter Two — Special Functions

11ProPress SP Furnace Operations Manual Set Vacuum LevelThe factory setting for vacuum is 71 cm of mercury. The acceptablerangeisfrom28cmto74–7

12ProPress SP Furnace Operations Manual Set Program Start DelayThe furnace has a unique feature that allows the operator to program a delay to occur b

13ProPress SP Furnace Operations Manual Saving Programs to a Flash Drive (Exporting)1. Place the Flash Drive in the USB slot on the left side of the f

14ProPress SP Furnace Operations Manual Low Fusing AdjustCalibration (800° C/1470° F or below)1. Select the Special Functions item from the Main Menu.

15ProPress SP Furnace Operations Manual Press Fusing AdjustConventional and SP Pressing Programs1. Select the Special Functions item from the Main Men

16ProPress SP Furnace Operations Manual Testing Your FurnaceThe Pro Series Furnaces are capable of performing several tests to aid in diagnosing the f

17ProPress SP Furnace Operations Manual Chapter Three — Change Program MenuLook at a ProgramThe Look at a Program feature allows the operator to view

18ProPress SP Furnace Operations Manual Add/Edit a ProgramAdd/Edit a Program is used to enter a new program or Editapre-existingprogram.This selec

19ProPress SP Furnace Operations Manual 11. Hold Temperature Hold Temperature or the top temperature is the final, highesttemperatureina1-StageP

2ProPress SP Furnace Operations Manual WarrantyUnited States and CanadaWhip Mix Corporation warrants the ProPress SP to the original purchaser against

20ProPress SP Furnace Operations Manual Introduction to Sense PressingIntroductionTime, Temperature, and PressureConventional pressings have classical

21ProPress SP Furnace Operations Manual loaded suddenly. Once the press rod is in contact with the moldplungertheother40%isapplied,bringingthe

22ProPress SP Furnace Operations Manual Add/Edit a Sense Press ProgramProgram EntryThe following steps will take you through the entry of SP PressPro

23ProPress SP Furnace Operations Manual The following procedures describe how to enter a Pressingprogram:1. Press the Main Menubutton:2. Select th

24ProPress SP Furnace Operations Manual Why do you need fusing adjustments?The Program Level Fusing Adjust is useful for making minoradjustmentstoa

25ProPress SP Furnace Operations Manual Copy/Change a ProgramThe Copy/Change a program feature allows a program to be copied from one program number t

26ProPress SP Furnace Operations Manual Turn the Selector Knob until the desired program is displayed. If the table has not been lowered, do so now.Pr

27ProPress SP Furnace Operations Manual The LED GraphThe LED graph follows the running Program’s progress and provides a quick visual reference on how

28ProPress SP Furnace Operations Manual Running a Pressing ProgramThe ProPress SP can press into a 100, 200, or 300 gram investment mold. Configure the

29ProPress SP Furnace Operations Manual Running a Re-Press Program(For Conventional Pressing only) TorunaRe-PressProgram,CalibrationPasswordnum

3ProPress SP Furnace Operations Manual Table of ContentsChapter Three — Change Program MenuLook at a Program ...

30ProPress SP Furnace Operations Manual Cleaning the FurnaceYour new furnace may be cleaned by using a soft cloth and kitchen cleaners such as Fantast

31ProPress SP Furnace Operations Manual Vacuum Test1. Press the Up arrow button to raise the table fully up. You cannot start a vacuum test until th

32ProPress SP Furnace Operations Manual Replacement PartsPart Number Description96004 Power Cord 115V96008 Power Cord 230V96001 Ceramic Plunger Rods P

33ProPress SP Furnace Operations Manual High-Efficiency Vacuum PumpProCal Pro Series Accessories

34ProPress SP Furnace Operations Manual Fahrenheit to Centigrade ° F ° C ° F ° C ° F ° C ° F ° C 100 38 630 332 1,160 627 1,690 921 1

4ProPress SP Furnace Operations Manual External Component LocatorSelector KnobVacuum Pump Hose BarbPower SwitchPower Inlet PlugFusesPressure Regulator

5ProPress SP Furnace Operations Manual Chapter One — Getting StartedYou are undoubtedly eager to unpack, set up, and begin using your new furnace. Get

6ProPress SP Furnace Operations Manual Quick-Cool Jet Installation Preparation:1. Remove the vacuum pump from its box.2. Remove the brass hose barb fr

7ProPress SP Furnace Operations Manual Power• Thefurnacerequires115Vacand12Ampsofcurrentin the United States and 220–240 Vac and 7.0 Amps o

8ProPress SP Furnace Operations Manual Menu SelectionThe three menu selection items (Run Program, Change Program and Special Functions) will display d

9ProPress SP Furnace Operations Manual Information Display and EntryDISPLAY — All information and user prompts will be shown on the display (four line